Untitled 2
 
back to landing page Home page About us Contact us


 

MODEL

9GBY-2.1

9GB-2.1 (HIGH)

CUTTING WIDTH - meter

2.1m

2.1m

WORKING SPEED – km/h

6-8 km/h

6-8 km/h

AVERAGE CUTTING SPEED – ha/h

0.8-1.5 ha/h

0.8-1.5 ha/h

AVERAGE CUTTING HEIGHT - mm

50-70mm

50-70mm

PTO SPEED - rpm

540rpm

540rpm

RECOMMENDED TRACTOR- kw

18-35kw

40—60kw

WEIGHT – kg

150kg

180kg

 

INFORMATION


THE ECO RECIPROTATING MOWER IS MAINLY USED TO CUT DIFFERENT GRASS TIPES.
IT IS CAN BE FOLDED VERTICALLY FOR TRANSPORT PURPOSES AND LOWERED HORIZONTALLY FOR CUTTING OR OPERATING TO COMMENCE.

 

NO

DISCRIPTION

1

WELDED FRAME

2

PTO

3

SUPPORT

4

CUTTER BAR

ADJUSTING


1 STRAP ADJUSTING
FIRST, PLEASE RELEASE THE BELT PULLEY BEARING BOLT.
SECOND, RELEASE THE LOCKNUTS ON THE REGULATING PLATE.
THIRD, TURNING THE BOLT ON THE MOWER COVER, PLEASE ADJUST THE BELT PULLEY ALWAYS UP OR  DOWN, ADJUST THE BELT TO HAVE THE PROPER ELASTICITY. THE PROPER ELASTICITY DEGREE IS WHEN YOU INFLICT ABOUT 2kg ON A SINGLE BELT, THE FLEXCIBILITYIS ABOUT 6mm.
FOURTH, FASTEN ALL BOLTS AND LOCK NUTS.
2 ADJUST LIMITATIVE MECHANISM
WHEN LIFTING THE CUTTER THE OUTER RUNNER SHOULD LEAVE THE GROUND BEFORE THE INNER RUNNER, AFTER THAT , YOU CAN LIFT THE CUTTER. YOU CAN DO THIS BY ADJUSTING THE TERMINAL STRAND.
3 CUTTER ADJUSTMENT
WHEN YOU PULL OR PUSH THE CONNECTING ROD, THE CUTTER SHOULD RUN PLACIDLY. WHEN YOU FEEL RESISTANCE, CHECK THE CLEARANCE OF THE PUSHING BROACH AND ADJUST
4 OBLIQUITY ADJUSTMENT
ADJUST THE TOP LINK TO ADJUST THE PITCH OF THE CUTTER BAR TIP. PLEASE ADJUST ACCORDING TO GROUND SURFACE STATUS.WHEN SMOOTH YOU MAY DECLINE THE CUTTING HEIGHT, WHEN RUGGED RAISE THE TIP TO AVOID BREAKING THE CUTTER BAR.
5 ADJUST THE KNIFE CLEARANCE
WHEN THE WOOD CONNECTING ROD IS AT ITS LIMIT, PLEASE KEEP THE KNIFE SECTION CLOSE TO THE FIXED BLADE (0,5mm CLEARANCE IS ALLOWABLE) THE BACK END CLEARANCE SHOULD BE 0,3 – 1.0mm.
ESPECIALLY, SOME CLEARANCE WILL BE ALLOWED 1,5mm, BUT THIS KIND OF CLEARANCE CAN’T BE OVER A 1/3 OF THE TOTAL. IF THE SPACE IS TOO LARGE, PLEASE THIN THE CUTTER PROTACTOR AND THE SURFACE OF THE GIRDER TO REDUCE THE SPACE.

ADJUST THE CLEARANCE BETWEEN THE KNIFE AND THE FIXED BLADE BY KNOCKING ON THE KNIFE HOLDER, THE CLEARANCE SHOULD BE LESS THAN 0,5mm.
MOVE THE FRICTION PLATE FORWARD TO MAKE THE FRICTION PLATE CLOSE TO THE TRAILING FLANK OF THE CUTTER HOLDER.
ADJUST THE CLEARANCE BETWEEN THE KNIFE TIP, KNIFE STEERING DEFLECTOR AND THE KNIFE TIP PROTECTOR, REPLACE OR ADJUST THE GASKET, MAKING THE STEERING DEFLECTOR OR THE FORWARD PROTECTOR THIN. CUT DOWN THE CLEARANCE BETWEEN THEM AND THE KNIFE TIP ( <1,5mm), THAT CAN ELIMINATE THE JUMPINESS OR THE IMPACT.
WHEN YOU WANT TO ADJUST THE CUTTING HEIGHT, PLEASE ADJUST THE BOTTOM PLATE OF THE INNER AND OUTER RUNNER.
ADJUST THE CLEARANCE BETWEEN THE KNIFE TIP BALL AND THE INNER-OUTER BALL SOCKET.PLEASE RELEASE THE SPRING PLATE, ADJUST THE COLUMN NUT POSITION WHICH IS THE CUP HEAD SQUARE NECK BOLT, KEEP THE CLEARANCE BETWEEN 0,3 AND 0,5mm. THE BIGGER CLEARANCE WILL INDUCE THE OVERSIZE WALLOP AND NOICE, THE SMALLER CLEARANCE WILL INDUCE THE CALORIFIC AND WEARING.

 

 

 

Copyright: Christmas Wonderland 2014

 

 

 

Copyright: Christmas Wonderland 2014